Head Honcho

May 1st at 9:33am

Thread Creator
New
#45
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

The following guides contain all OEM torque specifications for the Jeep Gladiator JT. These values are based on when the vehicle was launched in 2020 and may not account for newer powertrains, drivetrains, or part revisions.

Axles

Body
Brakes

Bumpers and Frame
Clutch
Cooling System
Driveshaft
EGR
Engine

Evap Canister
Exhaust
Fuel Delivery
Fuel Injection
HVAC
Restraints
Steering

Suspension

Transfer Case (Full-Time and Selec-Trac)
Transmission

Wheels
Wheel Bolts

Axle Lock

Head Honcho

May 1st at 9:51am

Thread Creator
New
#46
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Axle M210 Front

Part	Nm	ft. lbs.	Notes
Axle Shaft Nut	136 Nm	100 ft. lbs.	Replace fastener with new one.
Bearing Cap Bolts	108 Nm	80 ft. lbs.
Differential Cover Bolts	20 Nm + 20° Turn	15 ft. lbs. + 20° Turn
Differential Drain Plug	34 Nm	25 ft. lbs.
Differential Fill Plug	34 Nm	25 ft. lbs.
Pinion Flange Nut	217 Nm	160 ft. lbs.	Replace fastener with new one.
Ring Gear Bolts	136 Nm	100 ft. lbs.	Replace fastener with new one.
Front Axle Disconnect Skid Plate Bolts	42 Nm	31 ft. lbs.
Front Axle Disconnect Bolts	18 Nm	13 ft. lbs.	Replace fastener with new one.

Axle Lock

Head Honcho

May 1st at 10:28am

Thread Creator
New
#47
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Axle M220 Rear

Part	Nm	ft. lbs.	Notes
Axle retainer nut	80 Nm	59 ft. lbs.
Bearing cap bolts	95 Nm	70 ft. lbs.
Differential cover bolts	41 Nm	30 ft. lbs.	Replace fastener with new one.
Differential drain plug	34 Nm	25 ft. lbs.
Differential fill plug	34 Nm	25 ft. lbs.
Pinion nut	488 Nm	360 ft. lbs.	Replace fastener with new one.
Ring gear bolts	100 Nm + 57.5° Turn	74 ft. lbs. + 57.5° Turn	Replace fastener with new one.
Rear axle vent fitting	22 Nm	17 ft. lbs.

Axle Lock

Head Honcho

May 1st at 11:08am

Thread Creator
New
#48
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Body

Part	Nm	ft. lbs.	in. lbs.	Notes
A-pillar grab handle bolts	9 Nm	-	80 in. lbs.
B-pillar grab handle bolts	9 Nm	-	80 in. lbs.
B-pillar trim to sport bar	9 Nm	-	80 in. lbs.
Backlite to hard top bolts	11 Nm	8 ft. lbs.	-
Body isolator A-pillar bolt	125 Nm	92 ft. lbs.	-	Apply thread locking compound.
Body isolator B-pillar bolt - body bolt	108 Nm	80 ft. lbs.	-	Apply thread locking compound.
Body isolator B-pillar bolt - frame nuts	49 Nm	36 ft. lbs.	-
Body isolator C-pillar bolt - body bolt	125 Nm	92 ft. lbs.	-	Apply thread locking compound.
Body isolator C-pillar bolt - frame nuts	49 Nm	36 ft. lbs.	-
Body isolator front - body nuts	49 Nm	36 ft. lbs.	-
Body isolator front - frame nut	125 Nm	92 ft. lbs.	-
Bulkhead to instrument panel bolts	20 Nm	15 ft. lbs.	-
Cargo box hold down bolts	80 Nm	59 ft. lbs.	-
Cowl panel end bolts	9 Nm	-	80 in. lbs.
Cowl side panel to body bolts	8 Nm	-	71 in. lbs.
Door armrest bolts	8 Nm	-	71 in. lbs.
Door beam bracket to hinge pillar	23 Nm	17 ft. lbs.	-
Door carrier plate to door bolts	7 Nm	-	62 in. lbs.
Door check strap to door nuts	11 Nm	8 ft. lbs.	-
Door check strap to pillar bolt	9 Nm	-	80 in. lbs.
Door exterior handle screw	1.9 Nm	-	17 in. lbs.
Door exterior handle support bracket screw	1.9 Nm	-	17 in. lbs.
Door frame rail - front	8 Nm	-	71 in. lbs.
Door frame rail - rear	8 Nm	-	71 in. lbs.
Door glass channel to door nut	11 Nm	8 ft. lbs.	-
Door glass to regulator bolts	14 Nm	10 ft. lbs.	-
Door hinge pivot nuts	5 Nm	-	44 in. lbs.
Door hinge to door bolts	28 Nm	21 ft. lbs.	-
Door hinge to pillar bolts	48 Nm	35 ft. lbs.	-
Door interior handle bolt	7 Nm	-	62 in. lbs.
Door latch bolts	7 Nm	-	62 in. lbs.
Door striker bolts	17 Nm	13 ft. lbs.	-
Exterior mirror fasteners	6 Nm	-	53 in. lbs.
Fender to body bolts	7 Nm	-	62 in. lbs.
Folding top lift assist to sport bar bolts	14 Nm	10 ft. lbs.	-
Front fender flare bolts	7 Nm	-	62 in. lbs.
Front seat back bolts	73 Nm	54 ft. lbs.	-
Front seat track back bolts	48 Nm	36 ft. lbs.	-
Front seat track bolts	48 Nm	36 ft. lbs.	-
Front wheelhouse splash shield to fender flare screws	5 Nm	-	44 in. lbs.
Hard top front receiver bracket bolts	12 Nm	9 ft. lbs.	-
Hard top to B-pillar bolts	12 Nm	9 ft. lbs.	-
Hard top to body bolts	12 Nm	9 ft. lbs.	-
Hood catch bracket to hood nuts	5 Nm	-	44 in. lbs.
Hood catch to fender nuts	10 Nm	-	89 in. lbs.
Hood hinge to body bolts	25 Nm	18 ft. lbs.	-
Hood hinge to hood bolts	20 Nm	15 ft. lbs.	-
Hood pop up spring bolt	10 Nm	-	89 in. lbs.
Hood prop rod bolts	8 Nm	-	71 in. lbs.
Hood safety hook to hood bolts	10 Nm	-	89 in. lbs.
Instrument panel carrier bolts	12 Nm	9 ft. lbs.	-
Instrument panel cowl bolts	11 Nm	8 ft. lbs.	-
Instrument panel dash bolts	6 Nm	-	53 in. lbs.
Instrument panel to center floor bolt	10 Nm	-	89 in. lbs.
Instrument panel to center floor nut	10 Nm	-	89 in. lbs.
Power top assembly to body screws	5 Nm	-	44 in. lbs.
Radiator crossmember bolts	11 Nm	8 ft. lbs.	-
Radiator crossmember brace bolts	9 Nm	-	80 in. lbs.
Rearview mirror to header screw	6 Nm	-	56 in. lbs.
Second row seat bolts	48 Nm	36 ft. lbs.	-
Second row seat frame bolts	40 Nm	35 ft. lbs.	-
Second row seat pivot bolts	45 Nm	33 ft. lbs.	-
Side step/rock rail nuts	15 Nm	11 ft. lbs.	-
Side step/rock rail to body bolts	28 Nm	21 ft. lbs.	-
Soft top #1 bow cable bracket fasteners	5 Nm	-	44 in. lbs.
Soft top #1 bow to linkage fasteners	5 Nm	-	44 in. lbs.
Soft top #2 bow to linkage fasteners	7 Nm	-	62 in. lbs.
Soft top #3 bow to linkage fasteners	7 Nm	-	62 in. lbs.
Soft top #4 bow to linkage fasteners	7 Nm	-	62 in. lbs.
Soft top #5 bow to linkage fasteners	7 Nm	-	62 in. lbs.
Soft top center lower body rail fasteners	12 Nm	9 ft. lbs.	-
Soft top comer lower body rails fasteners	23 Nm	17 ft. lbs.	-
Soft top comer lower body rails to center rail fasteners	10 Nm	-	89 in. lbs.
Soft top J-rail retainer fasteners	7 Nm	-	62 in. lbs.
Soft top to front door rail fasteners	9 Nm	-	80 in. lbs.
Soft top to rear door rail fasteners	5 Nm	-	44 in. lbs.
Soft top upper door rail fasteners	4 Nm	-	35 in. lbs.
Tailgate cable to box anchor bolts	23 Nm	17 ft. lbs.	-
Tailgate cable to tailgate bolt	15 Nm	11 ft. lbs.	-
Tailgate cleat to cargo box fastener	16 Nm	12 ft. lbs.	-
Tailgate cover fasteners	7 Nm	-	62 in. lbs.
Tailgate latch bolts	18 Nm	13 ft. lbs.	-
Tailgate latch control assembly nuts	6 Nm	-	53 in. lbs.
Tailgate latch striker	20 Nm	15 ft. lbs.	-
Tailgate lock plate screw	23 Nm	17 ft. lbs.	-
Tailgate pivot bracket to box	65 Nm	48 ft. lbs.	-
Tailgate pivot bracket to tailgate	33 Nm	24 ft. lbs.	-
Tonneau bracket to bedside fasteners	5 Nm	-	44 in. lbs.
Tonneau bracket to bulkhead bolts	15 Nm	11 ft. lbs.	-
Trough cross body to body fasteners	5 Nm	-	44 in. lbs.
Trough left to body in white fasteners	5 Nm	-	44 in. lbs.
Utility rail fasteners	6 Nm	-	53 in. lbs.
Windshield frame to header bolts	17 Nm	12 ft. lbs.	-
Windshield hinge to cowl fram bolts	30 Nm	22 ft. lbs.	-
Windshield hinge to windshield frame bolts	25 Nm	18 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 11:27am

Thread Creator
New
#49
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Brakes

ABS

Part	Nm	ft. lbs.	in. lbs.
Anti-lock Brake System (ABS) Module Bolt	8 Nm	-	70 in. lbs.
Front Wheel Speed Sensor Bracket Bolt	30 Nm	22 ft. lbs.	-
Front Wheel Speed Sensors Bolt	7 Nm	-	62 in. lbs.
Hydraulic Control Unit (HCU) Bracket Bolts	5 Nm	-	44 in. lbs.
Hydraulic Control Unit (HCU) Brake Line Flare Nuts	20 Nm	15 ft. lbs.	-
Rear Wheel Speed Sensors Bolt	10 Nm	7 ft. lbs.	-

Brakes

Part	Nm	ft. lbs.	in. lbs.
Brake Booster Nuts	30 Nm	22 ft. lbs.	-
Brake Hose Frame Bolt	11 Nm	8 ft. lbs.	-
Brake Rotor Splash Shield Bolts	10 Nm	7 ft. lbs.	-
Electric Vacuum Pump (EVP) Bolts	8 Nm	-	71 in. lbs.
Electric Vacuum Pump (EVP) Bracket Bolts	25 Nm	18 ft. lbs.	-
Front Brake Hose Axle Bolt	8 Nm	-	71 in. lbs.
Front Brake Hose Lower Control Arm Nut	18 Nm	13 ft. lbs.	-
Front Brake Line Hose Flare Nut	20 Nm	15 ft. lbs.	-
Front Caliper Adapter Bolt	195 Nm	144 ft. lbs.	-
Front Caliper Bleed Screw	10 Nm	7 ft. lbs.	-
Front Caliper Bolts	37 Nm	27 ft. lbs.	-
Front Caliper Brake Hose Banjo Bolt	35 Nm	26 ft. lbs.	-
Front Rotor Screw	20 Nm	15 ft. lbs.	-
Master Cylinder Brake Line Flare Nuts	23 Nm	17 ft. lbs.	-
Master Cylinder Nuts	18 Nm	13 ft. lbs.	-
Park Brake Cable Boot Nuts	9 Nm	-	80 in. lbs.
Park Brake Cable Bracket Bolts	70 Nm	52 ft. lbs.	-
Park Brake Cable Guide Nut	11 Nm	8 ft. lbs.	-
Park Brake Lever Nuts	22 Nm	16 ft. lbs.	-
Park Brake Lever Sled Nuts	24 Nm	18 ft. lbs.	-
Pedal Sled Nuts	30 Nm	22 ft. lbs.	-
Primary Brake Line Flare Nut at Hydraulic Control Unit (HCU)	25 Nm	18 ft. lbs.	-
Rear Brake Line Hose Flare Nut	20 Nm	15 ft. lbs.	-
Rear Caliper Adapter Bolt	125 Nm	92 ft. lbs.	-
Rear Caliper Bleed Screw	10 Nm	7 ft. lbs.	-
Rear Caliper Bolts	37 Nm	27 ft. lbs.	-
Rear Caliper Brake Hose Banjo Bolt	35 Nm	26 ft. lbs.	-
Rear Rotor Screw	20 Nm	15 ft. lbs.	-
Secondary Brake Line Flare Nut at Hydraulic Control Unit (HCU)	18 Nm	13 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 11:34am

Thread Creator
New
#50
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Bumpers and Frame

Part	Nm	ft. lbs.	in. lbs.	Notes
Front Bumper Support Bracket Nuts	20 Nm	15 ft. lbs.	-
Front Bumper to Frame Nuts	90 Nm	66 ft. lbs.	-
Front Skid Piate Bracket to Frame Bracket Bolts	50 Nm	37 ft. lbs.	-
Front Skid Plate Bolts	25 Nm	18 ft. lbs.	-
Front Skid Plate Pencil Brace to Front Skid Plate Bracket	9 Nm	7 ft. lbs.	80 in. lbs.
Hitch to Frame Bolts	90 Nm	66 ft. lbs.	-
Rear Bumper Guard to Bracket Bolts	48 Nm	35 ft. lbs.	-	Replace fastener with new one.
Rear Bumper Guard to Bumper Bolts	48 Nm	35 ft. lbs.	-	Replace fastener with new one.
Rear Bumper to Hitch Bolts - Bottom	30 Nm	22 ft. lbs.	-
Rear Bumper to Hitch Bolts - Center	30 Nm	22 ft. lbs.	-
Rear Bumper to Hitch Nuts	30 Nm	22 ft. lbs.	-
Skid Plate Fuel Tank to Transmission Crossmember	65 Nm	48 ft. lbs.	-
Skid Plate to Frame	65 Nm	48 ft. lbs.	-
Tow Hook Bolts - Front	12 Nm	94 ft. lbs.	-
Tow Hook to Hitch Bolts	165 Nm	122 ft. lbs.	-
Trailer Hitch to Bracket Bolts	105 Nm	77 ft. lbs.	-
Trailer Hitch to Frame Bolts - Lower	165 Nm	122 ft. lbs.	-
Trailer Hitch to Frame Bolts - Rear	170 Nm	125 ft. lbs.	-
Transfer Case Skid Plate to Crossmember Bolts	75 Nm	55 ft. lbs.	-
Transfer Case Skid Plate to Frame Bolts	75 Nm	55 ft. lbs.	-
Transfer Case Skid Plate to Fuel Tank Nut	20 Nm	15 ft. lbs.	-
Transmission Crossmember to Bracket Bolts/Nuts	115 Nm	85 ft. lbs.	-
Transmission Crossmember to Frame Bolts	70 Nm	52 ft. lbs.	-
Transmission Crossmember to Skid Plate	65 Nm	48 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 11:40am

Thread Creator
New
#51
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Clutch

Part	Nm	ft. lbs.	in. lbs.	Notes
3.6L Pressure plate to flywheel bolts	30 Nm	22 ft. lbs.	-	Replace fastener with new one.
Clutch master cylinder nuts	17 Nm	13 ft. lbs.	-
Clutch pedal bracket to dash	20 Nm	15 ft. lbs.	-
Clutch pipe to transmission bolts	18 Nm	13 ft. lbs.	-
Clutch slave cylinder	10 Nm	-	89 in. lbs.
Flywheel to crankshaft bolts	52 Nm	38 ft. lbs.	-	Replace fastener with new one.

Axle Lock

Head Honcho

May 1st at 11:44am

Thread Creator
New
#52
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Cooling System

Part	Nm	ft. lbs.	in. lbs.
A/C condenser bolts	5 Nm	-	45 in. lbs.
Belt tensioner bolt	50 Nm	37 ft. lbs.	-
Block heater bolt	12 Nm	9 ft. lbs.	-
Coolant crossover bolts	11 Nm	8 ft. lbs.	-
Cooling fan bolts	8 Nm	71 ft. lbs.	-
Coolant recovery bottle bolts	10 Nm	-	89 in. lbs.
Left idler pulley bolts	25 Nm	18 ft. lbs.	-
Center idler pulley bracket M8 bolt	25 Nm	18 ft. lbs.	-
Center idler pulley bracket M10 bolt	55 Nm	41 ft. lbs.	-
Center idler pulley bracket to generator bolts	24 Nm	18 ft. lbs.	-
Center idler pulley bolt	50 Nm	37 ft. lbs.	-
Radiator brace bolt	10 Nm	-	89 in. lbs.
Radiator to body bolts	11 Nm	8 ft. lbs.	-
Right idler pulley bracket bolts	24 Nm	18 ft. lbs.	-
Right idler pulley bolt	25 Nm	18 ft. lbs.	-
Thermostat housing bolts	10 Nm	-	89 in. lbs.
Water pump M6 bolts	11 Nm	8 ft. lbs.	-
Water pump M8 bolts	23 Nm	17 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 11:49am

Thread Creator
New
#53
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Driveshaft

Part	Nm	ft. lbs.	Notes
Front driveshaft to front axle flange bolts	121 Nm	89 ft. lbs.	Replace fastener with new one. Torque and secure in a crisscross pattern.
Front driveshaft to transfer case flange bolts	39 Nm	29 ft. lbs.	Replace fastener with new one. Torque and secure in a crisscross pattern.
Rear driveshaft carrier bearing to frame	62 Nm	46 ft. lbs.
Rear driveshaft to transfer case flange bolts	39 Nm	29 ft. lbs.	Replace fastener with new one. Torque and secure in a crisscross pattern.
Rear driveshaft to rear axle flange bolts	39 Nm	29 ft. lbs.	Replace fastener with new one. Torque and secure in a crisscross pattern.

Axle Lock

Head Honcho

May 1st at 11:51am

Thread Creator
New
#54
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

EGR (Exhaust Gas Recirculation)

Part	Nm	ft. lbs.
EGR blocker plate to cylinder head	23 Nm	17 ft. lbs.
EGR cooler bracket nuts	23 Nm	17 ft. lbs.
EGR cooler tube to cylinder head	23 Nm	17 ft. lbs.
EGR temperature sensor	37 Nm	27 ft. lbs.
EGR tube to EGR valve	10 Nm	7 ft. lbs.
EGR tube to EGR cooler	10 Nm	7 ft. lbs.
EGR valve to intake manifold nuts	10 Nm	7 ft. lbs.

Axle Lock

Head Honcho

May 1st at 12:12pm

Thread Creator
New
#55
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Engine

Engine Block

Part	Nm	ft. lbs.	in. lbs.	Notes
Connecting Rod Cap Bolts	20 Nm + 90° Turn	15 ft. lbs. + 90° Turn	-	Replace fastener with new one.
Crankshaft Inner Main Bearing Cap M11 Bolts	20 Nm + 90° Turn	15 ft. lbs. + 90° Turn	-
Crankshaft Outer Main Bearing Cap and Windage Tray M8 Bolts	21 Nm + 90° Turn	15 ft. lbs. + 90° Turn	-
Crankshaft Position (CKP) Sensor To Engine Block M6 Bolt	12 Nm	9 ft. lbs.	-
Crankshaft Side Main Bearing Cap (Tie Bolt) M8 Bolts	30 Nm	22 ft. lbs.	-
Crankshaft Target Wheel To Counterweight Bolts	11 Nm	8 ft. lbs.	-	Replace fastener with new one.
Engine Block Ground Strap Bolt	23 Nm	17 ft. lbs.	-
Engine Block Ground Strap To Frame Nut	20 Nm	15 ft. lbs.	-
Engine Block Heater M6 Bolt	12 Nm	9 ft. lbs.	-
Lower Oil Pan To Upper Oil Pan - Bolts	9 Nm	-	80 in. lbs.
Lower Oil Pan To Upper Oil Pan - Nuts	10 Nm	7 ft. lbs.	-
Oil Cooler To Oil Filter Housing Screws	12 Nm	9 ft. lbs.	-
Oil Filter Housing Cap	25 Nm	18 ft. lbs.	-
Oil Filter Housing/Oil Cooler To Engine Block M6 Bolts	12 Nm	9 ft. lbs.	-
Oil Level Indicator To Cylinder Head Bolt	18 Nm	13 ft. lbs.	-
Oil Pan Drain Plug	27 Nm	20 ft. lbs.	-
Oil Pressure Sensor To Oil Filter Housing	20 Nm	-	177 in. lbs.
Oil Pump Pick Up Tube Bracket To Windage Tray M6 Bolt	12 Nm	9 ft. lbs.	-
Oil Pump Pick Up Tube To Oil Pump M6 Bolt	12 Nm	9 ft. lbs.	-
Oil Pump Sprocket M8 Bolt	26 Nm	18 ft. lbs.	-
Oil Pump To Engine Block M6 Bolts	12 Nm	9 ft. lbs.	-
Piston Oil Cooler Jet To Engine Block Bolt	6 Nm	-	53 in. lbs.
Upper Oil Pan To Engine Block M8 Bolts	23 Nm	17 ft. lbs.	-
Upper Oil Pan To Rear Seal Retainer M6 Bolts	10 Nm	7 ft. lbs.	-

Cylinder Head

Part	Nm	ft. lbs.	in. lbs.	Notes
Camshaft bearing cap	10 Nm	-	89 in. lbs.
Camshaft chain tensioner (primary) bolt	12 Nm	9 ft. lbs.	-
Camshaft chain guide (primary) bolt	12 Nm	9 ft. lbs.	-
Camshaft chain idler sprocket bolt	26 Nm	19 ft. lbs.	-
Camshaft chain LH tensioner (secondary) bolt	12 Nm	9 ft. lbs.	-
Camshaft chain LH guide (secondary) bolt	12 Nm	9 ft. lbs.	-
Camshaft chain RH tensioner (secondary) bolt	12 Nm	9 ft. lbs.	-
Camshaft chain RH guide (secondary) bolt	12 Nm	9 ft. lbs.	-
Camshaft position (CMP) sensor to cylinder head bolt	9 Nm	-	80 in. lbs.
Cylinder head coolant pipe plug	35 Nm	26 ft. lbs.	-	Replace fastener with new one.
Cylinder head oil restrictor M8 plug	18 Nm	13 ft. lbs.	-
Cylinder head cover M6 bolts	12 Nm	9 ft. lbs.	-
Catalytic converter to cylinder head M8 bolts	23 Nm	17 ft. lbs.	-
Fuel rail to lower intake manifold M6 bolts	7 Nm	-	62 in. lbs.
Heater hoses to cylinder head cover bracket	8 Nm	-	71 in. lbs.
Intake manifold (upper) M6 bolts	10 Nm	-	89 in. lbs.
Intake manifold (lower) M6 bolts	9 Nm	-	80 in. lbs.
Intake manifold support bracket lower M8 bolt	25 Nm	18 ft. lbs.	-
Intake manifold support bracket upper nuts	10 Nm	7 ft. lbs.	-
Oil control valve/cam phaser bolt - exhaust	150 Nm	118 ft. lbs.	-
Oil control valve/cam phaser bolt - intake	30 Nm + 45° Turn	22 ft. lbs. + 45° Turn	-
Oil temperature sensor to cylinder head	11 Nm	8 ft. lbs.	-	Replace fastener with new one.
Spark plug to cylinder head	18 Nm	13 ft. lbs.	-
Throttle body support bracket bolt	10 Nm	7 ft. lbs.	-
Throttle body support bracket bolt to front cover	10 Nm	7 ft. lbs.	-
Variable valve timing solenoid to cylinder head cover bolt	4 Nm	-	35 in. lbs.
Variable valve lift solenoid bolt	10 Nm	7 ft. lbs.	-
Wire harness retainer bracket to LH cylinder head bolts	10 Nm	7 ft. lbs.	-

Front Engine

Part	Nm	ft. lbs.
Coolant crossover housing to engine timing cover M6 bolts	12 Nm	9 ft. lbs.
Engine timing cover M6 bolts	12 Nm	9 ft. lbs.
Engine timing cover M8 bolt	25 Nm	18 ft. lbs.
Engine timing cover M10 bolts	55 Nm	41 ft. lbs.
Thermostat housing to coolant crossover M6 bolts	12 Nm	9 ft. lbs.
Vibration damper M16 bolt	40 Nm + 105° Turn	30 ft. lbs. + 105° Turn
Water pump to engine timing cover M6 bolts	12 Nm	9 ft. lbs.
Water pump to engine timing cover M8 bolt	25 Nm	18 ft. lbs.
Water pump to engine timing cover M10 bolt	55 Nm	41 ft. lbs.

Rear Engine

Part	Nm	ft. lbs.	Notes
Flexplate to crankshaft bolts	94 Nm	69 ft. lbs.	Replace fastener with new one.
Rear crankshaft oil seal retainer bolts	12 Nm	9 ft. lbs.
Torque converter to flexplate bolts	42 Nm	31 ft. lbs.	Replace fastener with new one.
Trans to engine block bolts	50 Nm	37 ft. lbs.
Trans to upper oil pan bolts	50 Nm	37 ft. lbs.

Engine Mounting

Part	Nm	ft. lbs.
Left Engine Mount Bracket to Engine Block Bolts	65 Nm	48 ft. lbs.
Left Engine Mount Isolator to Engine Mount Bracket Nut	122 Nm	90 ft. lbs.
Left Engine Mount Isolator to Frame Bolts	55 Nm	41 ft. lbs.
Rear Mount Isolator to Transmission Bolts	55 Nm	41 ft. lbs.
Rear Mount Isolator to Transmission Crossmember Nuts	175 Nm	129 ft. lbs.
Right Engine Mount Bracket to Engine Block Bolts	65 Nm	48 ft. lbs.
Right Engine Mount Isolator to Engine Mount Bracket Nut	122 Nm	90 ft. lbs.
Right Engine Mount Isolator to Frame Bolts	55 Nm	41 ft. lbs.

Miscellaneous Components

Part	Nm	ft. lbs.	in. lbs.
Air Cleaner Housing to Side Rail	5 Nm	-	44 in. lbs.
Air Cleaner Inlet Duct to Housing	4 Nm	-	35 in. lbs.
Air Cleaner Lid Bolts	4 Nm	-	35 in. lbs.
Air Cleaner Resonator to Shroud Bolts	3 Nm	-	27 in. lbs.
Air Inlet Hose Band Clamps	3 Nm	-	27 in. lbs.
Engine Cover Bracket to Cylinder Head Cover Bolts	7 Nm	-	62 in. lbs.
Engine Cover Bracket to Intake Manifold Bolts	8 Nm	-	71 in. lbs.
Engine Cover to Bracket Bolts	5 Nm	-	53 in. lbs.
Engine Lift Bracket	21 Nm	15 ft. lbs.	-
Heater Hose Assembly Support Bracket Bolts	8 Nm	-	71 in. lbs.
Heater Hose Assembly Support Bracket Nut	8 Nm	-	71 in. lbs.
Heater Hose Assembly to Bracket Nuts	8 Nm	-	71 in. lbs.

ECM

Part	Nm	ft. lbs.	in. lbs.
Amplifier To Body	5 Nm	-	44 in. lbs.
BCM To Body	5 Nm	-	44 in. lbs.
Central Vision Processing Module (CVPM) To Body Bolts	5 Nm	-	44 in. lbs.
DTCM Bracket Mounting Nuts	9 Nm	-	80 in. lbs.
EPB Nut	6 Nm	-	53 in. lbs.
ORC Module	11 Nm	8 ft. lbs.	-
Park Assist Module To BIW	3 Nm	-	26 in. lbs.
PCM Bracket To Body Bolts	6 Nm	-	53 in. lbs.
PCM Ground Wire Install	7 Nm	-	62 in. lbs.
PCM Ground Wire Nuts	7 Nm	-	62 in. lbs.
PCM To Bracket Bolts	8 Nm	-	71 in. lbs.
PCM To Bracket Nuts	8 Nm	-	71 in. lbs.
PDC Lower Cover Nuts	8 Nm	-	71 in. lbs.
PDC To Wiring Connector	5 Nm	-	44 in. lbs.
Power Inverter Module Bracket To IP	8 Nm	-	71 in. lbs.
RFH Module To bracket	9 Nm	-	80 in. lbs.
Security Gateway Module To Speaker Enclosure	5 Nm	-	44 in. lbs.
Steering Column Control Module Band Clamp Screw	6 Nm	-	53 in. lbs.
Tire Pressure Monitoring (TPM) Module Bracket Nuts	7 Nm	-	62 in. lbs.

Power Distribution

Part	Nm	in. lbs.
B+ Input to Power Distribution Center PDC Fasteners	8 Nm	71 in. lbs.
PDC Lower Cover Fastener	8 Nm	71 in. lbs.
PDC To Wire Harness Connector	5 Nm	44 in. lbs.

Ignition Controls

Part	Nm	ft. lbs.	in. lbs.	Notes
Camshaft Position Sensor Bolt	9 Nm	-	80 in. lbs.
Ignition Coil Capacitor Bolt	10 Nm	-	89 in. lbs.
Ignltion Coil Fasteners	8 Nm	-	71 in. lbs.
Knock Sensor	22 Nm	16 ft. lbs.	-	Replace fastener with new one.
Spark Plugs	20 Nm	15 ft. lbs.	-
Variable Valve Timing Solenoids	4 Nm	-	35 in. lbs.

Axle Lock

Head Honcho

May 1st at 12:43pm

Thread Creator
New
#56
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Evap Canister

Part	Nm	ft. lbs.
Vapor canister to vehicle bolts	6 Nm	4 ft. lbs.

Axle Lock

Head Honcho

May 1st at 12:44pm

Thread Creator
New
#57
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Exhaust

Part	Nm	ft. lbs.	in. lbs.
Catalytic converter to cylinder head bolts	24 Nm	18 ft. lbs.	-
Exhaust Y-Pipe to catalytic converter flange bolts	18 Nm	13 ft. lbs.	-
Front exhaust isolator bolts	30 Nm	22 ft. lbs.	-
Exhaust resonator clamp bolt	30 Nm	22 ft. lbs.	-
Heat shield nuts	3 Nm	-	27 in. lbs.
Muffler clamp nut	55 Nm	41 ft. lbs.	-
Muffler exhaust isolator bolts	25 Nm	18 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 12:53pm

Thread Creator
New
#58
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Fuel Delivery

Part	Nm	ft. lbs.	in. lbs.
Fuel Fill Tube Clamp	4 Nm	-	35 in. lbs.
Fuel Line Bundle To Transmission	25 Nm	18 ft. lbs.	-
Fuel Pump Control Module Nuts	6 Nm	-	53 in. lbs.
Fuel Rail To Intake Manifold Bolts	7 Nm	-	62 in. lbs.
Fuel Tank Deflector To Cross Member Bolt	8 Nm	-	70 in. lbs.
Fuel Tank Filler Tube Mounting Bracket Bolts	6 Nm	-	53 in. lbs.
Fuel Tank Skid Plate Bolts	95 Nm	70 ft. lbs.	-
Fuel Tank Strap To Skid Plate	25 Nm	18 ft. lbs.	-

Axle Lock

Head Honcho

May 1st at 12:54pm

Thread Creator
New
#59
Jump to PostCopy this target URL for a direct link to this post or click here to go there.

Fuel Injection

Part	Nm	ft. lbs.	in. lbs.
Accelerator pedal bolts	12 Nm	9 ft. lbs.	-
Crankshaft position sensor bolt	12 Nm	9 ft. lbs.	-
Fuel rail bolts	7 Nm	-	62 in. lbs.
Oxygen sensor (downstream)	43 Nm	32 ft. lbs.	-
Oxygen sensor (upstream)	43 Nm	32 ft. lbs.	-
Throttle body bolts	9 Nm	-	80 in. lbs.

Jeep Gladiator JT Torque Specs

Axle M210 Front

Axle M220 Rear

Body

Brakes

Bumpers and Frame

Clutch

Cooling System

Driveshaft

EGR (Exhaust Gas Recirculation)

Engine

Evap Canister

Exhaust

Fuel Delivery

Fuel Injection

Sign In

Create Account

Reset Password